Artikel zoeken
Informatie
Nieuw
- VoIP Telephones
- ISDN Interfaces
- Headsets
- Conference Solutions
- VoIP PBX
- Gateways
- Analog Adaptor ATA
- Switches
- Navayo
- TRex
- IP Door Phones
- Fax-Server
- WLAN + DECT over SIP
- IP Cameras
- Network Accessories
- Special Offers
- With PJP-50USB firmware Version 2.000 it is now possible to chain up to four PJP-50USBs for...
- Ga verder
- An upgrade to the popular Skype-certified GXV3140, the GXV3175 features a 7” touch screen...
- Ga verder
- New Fully-Featured 2-line GXP1450 Enterprise SIP Phone Delivers Innovative Desktop...
- Ga verder
- VoIP Media Gateway voip-mg The Junghanns .NET Voice over IP Media Gateway (voip-mg) turns all...
- Ga verder
- 42com's Open Source channel driver exclusively allows the combination of the flexible Asterisk-...
- Ga verder
U bent hier: / Analog Adaptor ATA / LINKSYS by CISCO SB
Artikel 1 / 2
Algemene Productinformatie
LINKSYS by CISCO SB SPA3102 ATA incl. Router
ArtNr: VOLSYSSPA3102
1 FXS, 1FXO and 2 Ethernet Ports ATA
Verzendklaar in 1-3 dagen.
- Description
Features at a Glance
- Service Authentication via PIN, Digest, Caller ID (Bellcore Type 1)
- Per Call Authentication and Associated Routing
- Least Cost Routing Support
- Impedance Agnostics - 8 Settings
- Call Waiting, Cancel Call Waiting, Call Waiting Caller ID Detection (Bellcore Type 1)
- Caller ID with Name/Number (Multi-national Variants)
- Caller ID Blocking
- Call Forwarding to PSTN or VoIP Service: No answer, Busy, All
- Do Not Disturb
- Call Transfer
- Three-way Conference Calling with Local Mixing
- Message Waiting Indication - Visual and Tone Based
- Call Return
- Call Back on Busy
- Call Blocking with Toll Restriction
- Delayed Disconnect
- Distinctive Ringing - Calling and Called Number
- Off-hook Warning Tone
- Selective/Anonymous Call Rejection
- Hot line and Warm Line Calling
- Speed Dialing of 8 Numbers/Addresses
- Music on Hold
- Fax: G.711 Pass Through or Real Time Fax over IP via T.38
Product Specific (SPA3102)
- Single Stage and Two Stage Dialing
- Forward Calls to VoIP service - Selective, Authenticated, All
- Forward Calls to PSTN service - Selective, Authenticated, All
- PSTN Line Sharing with Multiple Extensions
- Automatic PSTN Fallback (Loss of Power or IP Service to Unit - with Quiescence to Normal Operations)
- Advanced Inbound and Outbound Call Routing
- Independent Configurable Dial Plans - Up to 8
- Force PSTN Disconnection
- Sequential Dialing Support
VoIP to PSTN Authentication and Routing Features
- VoIP to PSTN Gateway Enable/Disable
- VoIP Caller Auth Method (None, PIN, HTTP Digest)
- VoIP PIN Max Retry Setting
- One Stage Dialing Enable/Disable
- VoIP Caller ID Pattern Matching
- VoIP Access Allowed Caller List (No Further Authentication)
- VoIP Caller PIN and Associated Dial Plan
PSTN to VoIP Authentication and Features
- PSTN to VoIP Gateway Enable/Disable
- VoIP Caller Auth Method (None, PIN, HTTP Digest)
- Ring Through to FXS Enable/Disable
- Ring Through Tone - Configurable
- Caller ID (Bellcore Type 1) for VoIP Service Access
- Caller ID Enable/Disable
- PIN Max Retry Settings
- Access Allowed Caller List (No Further Authentication)
- Caller PIN and Associated Dial Plan
- Least Cost Routing (via Outbound VoIP - Line1 Dial Plan)
FXO Behavior Features
- VoIP Answer Delay Timer
- PSTN Answer Delay Timer
- VoIP PIN Digit Time-Out Timer
- PSTN PIN Digit Time-Out Timer
- PSTN-to-VoIP Call Max Dur Timer
- VoIP-to PSTN Call Max Dur Timer
- PSTN Ring Through Delay Timer
- PSTN Dialing Delay Timer
- VoIP DIG Refresh Interval Timer
- PSTN Ring Time-out Timer
PSTN Disconnection Detection Features
- CPC (Removal of Tip/Ring Voltage Momentarily)
- Polarity Reversal
- Long Silence (Configurable Time Setting)
- Disconnect Tone (e.g. Reorder Tone)
- Silence Threshold
International Control Features
- FXO Port Impedance - Configurable to 16 settings
- Ring Frequency - Configurable
- SPA to PSTN and PSTN to SPA Gain Settings
- Ring Frequency - Maximum Setting
- Ring Validation Time Setting
- Tip/Ring Voltage Adjustment Setting
- Ring Indication Delay Setting
- Operational Loop Current Minimum Value
- Ring Time-out Setting
- On-Hook Speed Setting
- Ringer Impedance Setting
- Line-in-Use Voltage Setting
Artikel 1 / 2
